RO雷火平台（中国）股份有限公司官网膜现货技术争先
此外，纳滤出水是低腐蚀性的，对饮用水管网的使用期和管道金属离子的溶出有正面的影响，有利于保护配水系统的所有材科。试验表明采用必要后处理的纳滤膜系统能够使管网中铅的溶解减少50%，同时使其他溶出的金属离子浓度满足饮水水质标准要求。挥发性有机物(VOC)的去除：对饮用水中痕量挥发性有机物具有较的去除率。以上文章来源雷火平台（中国）股份有限公司官网的小编整理的，如有什么需求，欢迎来电咨询。
颗粒炭不易流失，可再生重复使用，用于污染较轻，需连续运行的水处理工艺。粉末炭不易回收，一般为一次性使用，用于间歇的污染较严重的水处理工艺。给水处理的颗料活性炭一般微孔和中孔发达，应符合三项要求：吸附容量大、吸附速度快、机械强度好。粉末活性炭要求除具备以上特点外，粒度越小吸附效果越好。活性炭材料在自来水供水中的应用情况活性炭的吸附可分为物理吸附和化学吸附。物理吸附主要发生在活性炭丰富的微孔中，用于去除水和空气中杂质，这些杂质的分子直径必须小于活性炭的孔径。不同的原材料和加工工艺造成活性炭不同的微孔结构、比表面积和孔径，适用于不同的需求。活性炭不仅含有碳元素，而且在其表面含有官能团，与被吸附的物质发生化学反应，从而与被吸附物质常发生在活性炭的表面。介质中的杂质通过物理吸附和化学吸附不断进入活性炭的多孔结构中，使活性炭吸附饱和、吸附效果下降。吸附饱和后的活性炭需要进行活化再生，恢复其吸附能力，重复使用。评价活性炭的吸附性能指标主要有亚甲蓝值、碘值和焦糖吸附值等，吸附容量越大，吸附效果越好。
雷火平台（中国）股份有限公司官网经营范围为各类水处理设备与相关产品，包括生活污水处理设备，一体化污水处理设备，农村污水处理设备，化工，工业污水设备，养殖污水处理设备，屠宰污水处理设备，食品污水处理设备，豆制品污水处理设备，地埋式污水处理设备，洗涤污水处理设备，洗车污水处理设备，涂装电泳污水处理，垃圾渗透液污水处理，MBR污水处理，餐饮酒店污水处理设备。未来雷火平台（中国）股份有限公司官网将继续专注于污水处理产品的开发和应用，努力为用户提供更好的产品和优质的服务!
防冻：树脂的保存环境需在周围环境>40℃情况下，如果温度低于5℃，为防止树脂结冰，可以把树脂放在食盐水溶液中。防干：由于树脂在使用或储运中水份消失，导致树脂体积忽胀忽缩，从而造成树脂的破碎或机械强度降低，丧失或降低了离子交换能力。在发生此种情况时，切不可把树脂直接投落水中，而是先将其浸泡于饱和食盐水中，使其缓慢膨胀不致破碎。
第二步是将树脂均匀地装入树脂罐中。取下中心管的封口胶带，将中心管上部及树脂罐端面用水冲洗并擦干净，中心管及控制器密封圈处涂上硅油。这个步骤也是对控制器进行防护，在使用也是很好的保护作用。第三步是将下布水器与中心管必须严密，注意：上布水器与控制阀、中心管。防止树脂跑出。中心管与控制阀必需严密不漏水，否则会出现窜硬水现象。上布水器安装到控制阀上，然后将中心管从上布水器内插入到控制阀内。小心地沿顺时针方向转动控制阀，直至旋紧在树脂罐接口上(或用法兰连接固定)一定要确保中心管插入阀体。安装完后要进行仔细检查，及时改善漏洞的出现，保证其工作效率。
同时，雷火平台（中国）股份有限公司官网还是西南地区专业配备有水质检测化验室的水处理设备公司。
进来有人在咨询水处理行业为什么要使用臭氧？今天和小编一起来了解一下吧：臭氧是强氧化剂，含有微量合成有机污染物的水质，常规水处理工艺不能解除，使用臭氧去氧化，使得不容易被生物降解的COD化学需氧量，变成BOD可生物降解的耗氧量，再用生物处理来解决水污染问题。生物处理经济实惠，所以当生物处理污水处理到一定程度后，使用臭氧，再用生物处理，可以除去少量的污染物。
（7）一次冲洗：采用不锈钢半自动冲瓶机对瓶子的内、外壁进行清洗，清洗的水量可调。（8）二次冲洗（水源为纯净水）：可采用不锈钢半自动冲瓶机对瓶子的内、外壁进行清洗，清洗的水量可调。如有什么需求，请来电咨询。雷火平台（中国）股份有限公司官网浅谈软水和硬水的区别：软水与硬水
工作态度吸引和培养了一批又一批的专业性人才。公司为客户提供的售前、售中和售后服务，速度快捷、态度真诚、服务质量完善，得到同行业及广大用户的高度赞赏和大力支持!
净水器使用注意事项四：正确清洗净水器清洗净水器一般是净水器放在干净的盆中，将过滤的芯上下拧开，上层的圆盖打开后，有两层无纺棉布，用新的牙刷轻轻的放在水里刷干净，下层有个塑料盖拧开，里面也有两层无纺棉布和沙石，各自轻轻的放在水里刷干净，再把过滤芯放入水后上下摇晃几下，比较后将净水器用水冲洗干净，并按原来的样子安装即可，大约每隔一个月左右，就要清洗一次。
R0膜对C02等小分子没有去除能力，因此雷火平台（中国）股份有限公司官网出水pH偏酸性，根据用途需要对其进行脱除或加碱调整pH值。由于水中没有余氯，如果出水需要长距离输送使用，必须投加消毒剂，并维持一定的余氯量。定时分析进水水质和透过水的水质，尤其是要严格控制进水水质，确保进水的预处理措施运行可靠，以保证进水的SDI在3以下。当透过水水量降低过多或水质不合格时，要立即对膜进行清洗再生，如果再生后仍不见好转，就应当及时更换膜组件，欢迎来电咨询重庆雷火平台（中国）股份有限公司官网净。
二，水处理设备的种类？目前市场中的水处理产品有很多，但是使用水处理要根据不同的情况、根据用户的使用水的要求来进行选用，不能一概而论的。水处理设备根据使用材料的不同，采用滤芯的不同，分为净水机，纯水机，软水机。净水机：净水机的种类也是很多的，根据使用滤芯的多少分为粗滤净水机：一般使用PP纤维棉、活性炭，有一级滤芯净水机、二级滤芯净水机、三级滤芯净水机、四级滤芯净水机和五级滤芯净水机。同时根据使用的中心技术的不同也分为粗级过滤、中空纤维精密过滤、陶瓷滤芯精密过滤。主要看使用的是什么样的滤芯。
我公司以：诚信的经营理念、服务创造水处理事业未来。
以：优质的品质、不断创新、完善的售后服务是我公司不断追求的目标。
愿与各界同行共同打造蓝天碧水、给你一个洁净的家园。
蒸馏法水处理技术蒸馏法是指将水煮沸，然后收集蒸汽，使之冷却和凝结成液体。蒸馏水是极安全的饮用水，但有一些问题要进一步探讨。由于蒸馏水不含矿物质，这成为反对者提出人的寿命容易老化的理由。另外利用蒸馏法成本较高，耗费能源，不能去除水中挥发性物质。煮沸法水处理技术煮沸法是指自来水煮沸后饮用，这是一种古老的方法，在国内普遍地应用。水煮沸可杀死，但对一些化学物质和重金属不能去除，即使其含量极低，所以饮用仍是不安全的。
RO雷火平台（中国）股份有限公司官网膜现货技术争先
RO reverse osmosis membrane spot technology
In addition, the nanofiltration water is low corrosive, has a positive impact on the service life of the drinking water pipe network and the dissolution of metal ions in the pipeline, and is beneficial to protect all materials of the water distribution system. The results show that the application of the nanofiltration membrane system can reduce the dissolution of lead by 50%, and the concentration of other dissolved metal ions can meet the requirements of drinking water quality standard. Volatile organic compounds (vocs) removal: the removal rate of trace vocs in drinking water is good. Above article source chongqing bi pure purification equipment co., LTD. Small make up, if there is any demand, welcome to inquire.
Carbon particles are not easy to lose, can be recycled, used for less pollution, continuous operation of the water treatment process. Powder carbon is not easy to recover, generally used for one-time use, used for intermittent water treatment process with serious pollution. The microporous and mesoporous activated carbon of feed water treatment should meet three requirements: large adsorption capacity, fast adsorption speed, good mechanical strength. In addition to the above characteristics, the smaller the particle size, the better the adsorption effect. The adsorption of activated carbon can be divided into physical adsorption and chemical adsorption. Physical adsorption mainly occurs in activated carbon rich micropores, used to remove impurities in water and air, the molecular diameter of these impurities must be smaller than the diameter of activated carbon. Different raw materials and processing processes result in different microporous structure, specific surface area and pore diameter of activated carbon, which is suitable for different needs. Activated carbon not only contains carbon elements, but also contains functional groups on its surface, which can react with adsorbed substances, and adsorbed substances often occur on the surface of activated carbon. Impurities in the medium continuously enter the porous structure of activated carbon through physical adsorption and chemical adsorption, so that the adsorption saturation of activated carbon, adsorption effect decreased. After adsorption saturation, activated carbon needs to be activated and regenerated to restore its adsorption capacity and reuse. The adsorption performance indexes of activated carbon were mainly methylene blue value, iodine value and caramel adsorption value, etc. The larger the adsorption capacity, the better the adsorption effect.
Chongqing green pure purification equipment co., LTD. Business scope for all kinds of water treatment equipment and related products, including sewage treatment equipment, the integration of sewage treatment facilities, the rural sewage treatment equipment, chemicals, industrial sewage equipment, aquaculture wastewater treatment equipment, slaughter wastewater treatment equipment, food, sewage treatment equipment, bean products wastewater treatment equipment, buried sewage treatment equipment, washing wastewater treatment equipment, car washing wastewater treatment equipment, electrophoresis coating wastewater treatment, garbage infiltration liquid sewage treatment, the MBR wastewater treatment, food and beverage hotel wastewater treatment equipment. In the future, we will continue to focus on the development and application of sewage treatment products, and strive to provide users with better products and quality services!
Antifreeze: the preservation environment of the resin should be in the surrounding environment >40℃, if the temperature is lower than 5℃, in order to prevent the resin from freezing, the resin can be placed in an aqueous solution of table salt. Antidryness: because the water content of the resin disappears in use or storage, the volume of the resin expands and shrinks, which leads to the crushing or mechanical strength reduction of the resin and the loss or reduction of the ion exchange capacity. In this case, do not throw the resin directly into the water, but first soak it in saturated salt water, so that it slowly expand not broken.
The second step is to evenly load the resin into the resin tank. Remove the sealing tape of the center tube, rinse the upper part of the center tube and the end face of the resin tank with water and wipe clean, and coat the sealing ring of the center tube and controller with silicone oil. This step is also to protect the controller, in use is also a good protection. The third step is the water distributor and center tube must be tight, pay attention to: the water distributor and control valve, center tube. Prevent the resin from escaping. The center pipe and control valve must be tight and watertight, otherwise there will be channeling hard water phenomenon. The water distributor is installed on the control valve and the center tube is inserted into the control valve from the water distributor. Carefully turn the control valve clockwise until it is tightened to the resin tank interface (or secured with a flange). Make sure the center tube is inserted into the valve body. After the installation should be carefully checked, timely improve the emergence of vulnerabilities, to ensure its work efficiency.
At the same time, chongqing bichun purification equipment co., LTD is also a professional water treatment equipment company equipped with water quality testing laboratories in southwest China.
Somebody came in and asked the water treatment industry why they use ozone? Today and the small make up together to learn about: ozone is a strong oxidizer, contain traces of synthetic organic pollutants of water quality, conventional water treatment process cannot remove, using ozone oxidation, make not easily biodegradable COD chemical oxygen demand (COD), become BOD biodegradable oxygen consumption, to solve the water pollution problems in biological treatment. Biological treatment is economical, so when biological treatment sewage treatment to a certain extent, the use of ozone, and then biological treatment, can remove a small number of pollutants.
(7) one rinse: the stainless steel semi-automatic bottle rinsing machine is used to clean the inner and outer walls of the bottle with adjustable water volume. (8) secondary flushing (water source is pure water) : stainless steel semi-automatic bottle punching machine can be used to clean the inner and outer walls of the bottle, the amount of water can be adjusted. If you have any demand, please call us. Chongqing bichun purification equipment co., LTD. On the difference between soft water and hard water: soft water and hard water
Working attitude attracts and trains a batch of professional talents. Company to provide customers with a full range of pre-sales, sales and after-sales service, fast speed, sincere attitude, service quality improvement, the industry and the majority of users highly appreciated and strongly supported!
Water purifier using note 4: correct cleaning water purifiers clean water purifier water on a clean basin commonly, unscrew the filtering core of up and down the upper on the dome, there are two layers of non-woven cloth, with a new toothbrush brush gently in the water is clean, the lower unscrewed a plastic cover, there are two layers of non-woven cotton and sand, each brush clean gently in the water, then put a filter in the water after the shake up and down, the final rinse water purifiers, and can be installed according to the original appearance, about every other month or so, will be clean.
R0 membrane has no ability to remove small molecules such as C02, so the pH of reverse osmosis water is more acidic. Remove or add alkali to adjust the pH value according to the application. Since there is no residual chlorine in the water, if the water needs to be transported over a long distance, disinfectant must be added and a certain amount of residual chlorine maintained. Analyze the incoming water quality and the water quality through the water regularly. In particular, strictly control the incoming water quality to ensure the reliable operation of the pre-treatment measures to ensure that the SDI of the incoming water is below 3. When the amount of water through the reduction of excessive or unqualified water quality, to immediately clean the membrane regeneration, if the regeneration is still not improved, it should be timely replacement of membrane components, welcome to inquire chongqing bi pure.
Ii. Types of water treatment equipment? There are a lot of water treatment products in the market at present, but the use of water treatment according to different circumstances, according to the user's water requirements to choose, can not be generalized. Water treatment equipment according to the use of different materials, the use of different filter elements, divided into water purifier, pure water machine, soft water machine. Water purifier: the type of water purifier is also a lot of, according to the use of the number of filter is divided into coarse filter water purifier: the general use of PP fiber cotton, activated carbon, there is a primary filter water purifier, secondary filter water purifier, three filter water purifier, four filter water purifier and five filter water purifier. At the same time according to the use of different central technology is also divided into coarse filtration, hollow fiber precision filtration, ceramic filter element precision filtration. It mainly depends on what kind of filter element is used.
Our company to: integrity of the business philosophy, service to create the future of water treatment business.
To: high quality, continuous innovation, perfect after - sales service is the company's constant pursuit of the goal.
Willing to create blue sky and clear water with all walks of life together, to give you a clean home.
Distillation water treatment technology distillation is the boiling of water and the collection of steam to cool it and condense it into a liquid. Distilled water is extremely safe drinking water, but there are some issues that need to be explored further. Since distilled water contains no minerals, this has led opponents to argue that people tend to age over their lifetimes. In addition, distillation has high cost, consumes energy and cannot remove volatile substances in water. Boiling method water treatment technology boiling method refers to drinking tap water after boiling, this is an ancient method, widely used in China. Boiling water can kill, but it can't remove some chemicals and heavy metals, even in very low levels, so it's still not safe to drink.
RO reverse osmosis membrane spot technology
